Features 

External (key-switch operated):

• Reset/resound/test zone lamps evacuate

• Silence alarm sounders

• Silence fault sounders

Internal:

• One man detector test

• Zone isolate

• Revert to short-circuit: fire (no resistors in call points)

External indicators:

• Sounder fault

• Battery/power supply fault

• Mains on

• Zone fire

• Zone fault

Internal indicators:

• Open circuit zone fault

• Short circuit zone fault

• Zone isolated

• Engineer test selected

Outputs:

• Two sounder circuits (alarm relay contacts can be obtained by connecting a relay to a sounder circuit)

Ancillary connections for expansion modules will allow the following:

• Repeater panels

• Multiple sounder outputs

• Connection to landlord panel

 

 Specifications 

	2 (0.8A SUPPLY)	4 / 6 (1.5A SUPPLY)	8/10/12/14/16/18 (4.0A SUPPLY)
POWER SPECIFICATION
MAINS SUPPLY VOLTAGE	230V±10%Va.c.50/60Hz	230V±10%Va.c.50/60Hz	230V±10%Va.c.50/60Hz
INTERNAL POWER SUPPLY	27 Vd.c.	27 Vd.c.	27 Vd.c.
TOTAL OUTPUT CURRENT LIMITED TO	800mA@240VAC	1500mA@240VAC	4000mA@240VAC
AUXILIARY POWER OUTPUT	27 Vd.c.	27 Vd.c.	27 Vd.c.
MAINS SUPPLY MONITORED FOR FAILURE	YES	YES	YES
BATTERY CHARGER MONITORED FOR FAILURE	YES	YES	YES
BATTERIES MONITORED FOR DISCONNECTION AND FAILURE	YES	YES	YES
DETECTOR CIRCUIT SPECIFICATION
NUMBER OF CIRCUITS	2	4 or 6	8, 10, 12, 14,16,or 18
LINE FAULT MONITORED FOR OPEN CIRCUIT	YES	YES	YES
LINE FAULT MONITORED FOR SHORT CIRCUIT	YES (Can be disabled)	YES (Can be disabled)	YES (Can be disabled)
LINE FAULT MONITORED FOR DETECTOR REMOVAL	Yes, if End of Line Monitor Unit fitted in place of End of Line Resistor
END OF LINE RESISTOR (SUPPLIED) VALUE	6800Ω,5% tolerance,0.25W	6800Ω,5% tolerance,0.25W	6800Ω,5% tolerance,0.25W
DETECTOR CONTINUITY DIODES	Silicon 1N4001 or Schottky type(required if End of Line Monitor Unit fitted to give Detector Removal Fault)
CALL POINT RESISTOR VALUE (NOT SUPPLIED)	470 to 680Ω, 0.5W	470 to 680Ω, 0.5W	470 to 680Ω, 0.5W
MAXIMUM NUMBER OF SMOKE DETECTORS PER ZONE	20(maximum detector current = 2mA)	20(maximum detector current = 2mA)	20(maximum detector current = 2mA)
MAXIMUM NUMBER OF MANUAL  CALL POINTS PER ZONE	No limit	No limit	No limit
SOUNDER CIRCUIT SPECIFICATION
NUMBER OF CIRCUITS	2	2	2
END OF LINE RESISTOR VALUE	6800Ω, 5%tolerance,0.25W	6800Ω, 5%tolerance,0.25W	6800Ω, 5%tolerance,0.25W
LINE FAULT MONITORED  FOR OPEN CIRCUIT	YES	YES	YES
LINE FAULT MONITORED FOR SHORT CIRCUIT	YES	YES	YES
OUTPUTS FUSED AT	1 Amp	1 Amp	1.6 Amp
MAXIMUM TOTAL OUTPUT CURRENT ALL OUTPUTS	800mA	1500mA	4000mA
MAXIMUM NO OF BELLS @ 25 mA EACH BELL	32	56	120
MAXIMUM NO OF ELECTRONIC SOUNDERS @ 20 mA	40	70	150
AUXILIARY RELAY CONTACTS  (DO NOT CONNECT MAINS VOLTAGES)	1A 30 Vd.c. max  Voltage Free	1A 31 Vd.c. max  Voltage Free	1A 32 Vd.c. max  Voltage Free
FUSES-ALL FUSES COMPLIANT TO IEC (EN60127 PT2)
MAINS TERMINAL BLOCK	200mA T 20 mm	400mA T 20mm	630mA T 20mm
SOUNDER OUTPUTS	1A F 20mm	1A F 20mm	1.6A F 20mm
AUXILIARY OUTPUT	1A F 20mm	1A F 20mm	1A F 20mm
BATTERY FUSE	1.6A F 20mm	1.6A F 20mm	3A F 20mm
DOOR RETAINING MAGNETS	DO NOT USE PANEL POWER SUPPLY AS YOU WILL DRASTICALLY REDUCE BATTERY STAND-BY TIME
CONNECTION BLOCK
LARGEST ACCEPTABLE CONDUCTOR SIZE	2.5mm2	2.5mm2	2.5mm2
SMALLEST ACCEPTABLE CONDUCTOR SIZE	0.75mm2	0.75mm2	0.75mm2
DIMENSIONS
ENCLOSURE(WIDTH x HEIGHT x DEPTH)	415 x 265 x 100mm	415 x 265 x 100mm	415 x 265 x 100mm
WEIGHT(WITHOUT BATTERIES)	5100g	5200g	5500g